Ptcl Wireless Huawei Modem Driver For Mac

Aug 04, 2015  What you need is a wireless repeater not a modem with built in router. A modem with built in router cannot be used for this purpose. At the most it may be possible to use it as a switch but using it to repeat your signal would require a lot of work and it is just not worth it.

• Ptcl Wireless Huawei Modem Driver For Mac Windows 10
• Huawei Usb Modem Driver Download

PTCL Evo connection comes with ZTE AC2726 USB modem. Its really easy to use it on Windows and Mac as there drivers are provided in the modem's memory but to use it on Linux is a bit tricky. Recently I succeeded in installing and configuring it on Ubuntu 9.10 and below are the steps which worked for me. When you attach the modem to your linux machine it gets detected as a usb storage device and not as a usb modem. To use it as usb modem we need to convert it from usb-storage device to usbserial device in ubuntu. To do this I used -modeswitch utility which can be installed using following command: sudo apt-get install usb-modeswitchUnplug the modem and plug it back in.

Use lsusb command to see list of usb devices attached to your system. You should see a line similar to Bus xxx Device xxx: ID 19d2:fff1Here 19d2 is vendor id for ZTE and fff1 is the device id for AC2726. If you dont see this line or see one with device id fff5 then you will need to restart your system.

• Here is a step by step guide to installing Vfone (Huawei) on Windows Vista. Plug in the data cable. Following box will appear. 3.Click on Locate and install Driver Software.
• TP-Link Wireless Router (WiFi) drivers are tiny programs that enable your Wireless Router (WiFi) hardware to communicate with your operating system software.

Now issue following command to load proper driver module in kernel: sudo modprobe usbserial vendor=0x19d2 product=0xfff1And thats it. Your modem is ready to be used. You will now need a dialer app to dial and establish the connection. I used gnome-ppp as it has the ability to dock. To install gnome-ppp issue following command: sudo apt-get install gnome-pppYou can now run gnome-ppp. You will need to run it as root.

After it starts click on setup. On setup window click Detect so that it can detect your usb modem. Set type to be USB MODEM and speed to be 460800. Set phone line to Tone and volume to off.

Now go to options tab and check the following:. Dock in notification area. Auto reconnect. Ignore terminal strings. Now click close. You will be taken back to smaller window.

Enter vwireless@ptcl.com as user name and ptcl as password. Enter #777 as phone number and click connect. And you will get connected to ptcl evo service.

UPDATE: if you are using Ubuntu 10.04 or later you can use a simpler method mentioned. That's good, kindly give some idea to connect HUAWEI Fixed Wireless Terminal ETS-2558 in UBUNTU 9.10, in another post some one did so but for Fedora 9.

I have done all above and my usb is Ptcl EVO Huawei gnome-ppp detected my modem and usb0 but while dialing the no. Following log file created and not connected.

LOGs of gnome-ppp - WvDial: Internet dialer version 1.60 - Cannot get information for serial port. Initializing modem. Sending: ATX3 ATX3 OK - Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 OK - Modem initialized. Please enter password (or empty password to stop): - Sending: ATM0L0DT#777 - Waiting for carrier. ATM0L0DT#777 CONNECT 3100000 - Carrier detected.

Starting PPP immediately. Unable to run /usr/sbin/pppd. Check permissions, or specify a 'PPPD Path' option in wvdial.conf. ^DSDORMANT:1 - Timed out while dialing. Trying again.

Maximum Attempts Exceeded.Aborting!! - Disconnecting at Sat May 29 09. Hay i am new to ubuntu, i have installed ubunutu 10.10, i have vptcl wireless huawei est2552 set, i am unable to conncet to internet using this set, plz help me, n iam using 64 bit dell inspron, When i attach the cable it gets detected as a usb storage device and not as a usb modem i used this command to covert it,as mentioned here sudo apt-get install usb-modeswitch it gives the following output Reading package lists. Done Building dependency tree Reading state information. Done usb-modeswitch is already the newest version. 0 upgraded, 0 newly installed, 0 to remove and 158 not upgraded.

1 not fully installed or removed. After this operation, 0B of additional disk space will be used. Do you want to continue thn i Unplug the modem and plug it back in. Use lsusb command to see usb modem it gives folloowing output Bus 002 Device 004: ID 12d1:1010 Huawei Technologies Co., Ltd. Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 012: ID 413c:8162 Dell Computer Corp.

Bus 001 Device 011: ID 413c:8161 Dell Computer Corp. Bus 001 Device 010: ID 0a5c:4500 Broadcom Corp. BCM2046B1 USB 2.0 Hub (part of BCM2046 Bluetooth) Bus 001 Device 005: ID 0bda:0158 Realtek Semiconductor Corp. USB 2.0 multicard reader Bus 001 Device 004: ID 0c45:641d Microdia Bus 001 Device 002: ID 8087:0020 Intel Corp.

Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub i donot konw what to do further, and am i going in a correct way, plzzzzz help me in connecting net in ubuntu10.10. Hay i am new to ubuntu, i have installed ubunutu 10.10, i have vptcl wireless huawei est2552 set, i am unable to conncet to internet using this set, plz help me, n iam using 64 bit dell inspron, When i attach the cable it gets detected as a usb storage device and not as a usb modem i used this command to covert it,as mentioned here sudo apt-get install usb-modeswitch it gives the following output Reading package lists. Done Building dependency tree Reading state information. Done usb-modeswitch is already the newest version.

0 upgraded, 0 newly installed, 0 to remove and 158 not upgraded. 1 not fully installed or removed. After this operation, 0B of additional disk space will be used. Do you want to continue thn i Unplug the modem and plug it back in.

Ptcl Wireless Huawei Modem Driver For Mac Windows 10

Use lsusb command to see usb modem it gives folloowing output Bus 002 Device 004: ID 12d1:1010 Huawei Technologies Co., Ltd. Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 012: ID 413c:8162 Dell Computer Corp. Bus 001 Device 011: ID 413c:8161 Dell Computer Corp. Bus 001 Device 010: ID 0a5c:4500 Broadcom Corp. BCM2046B1 USB 2.0 Hub (part of BCM2046 Bluetooth) Bus 001 Device 005: ID 0bda:0158 Realtek Semiconductor Corp. USB 2.0 multicard reader Bus 001 Device 004: ID 0c45:641d Microdia Bus 001 Device 002: ID 8087:0020 Intel Corp.

Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub i donot konw what to do further, and am i going in a correct way, plzzzzz help me in connecting net in ubuntu10.10. Incase anyone wants to use (the ZTE one) for ubuntu (10.04), I installed the usb modeswitches package (as indicated by the author) and then went to Preferences - Network Connections - Mobile Broadband.

It had the ZTE device showing up already in the drop down, just select it move next, select Pakistan move next and then in the next screen manually enter ptcl as the server provider name. Then you'll be prompted for the standard username and password. Save it and bingo. From the top network icon, just select your connection and it should connect directly. @aakhan: The file you downloaded is a zipfile. First you need to unzip the file. To do that Right-Click on the file and click extract here.

Huawei Usb Modem Driver Download

This will create a directory 'linux SW'. Open linux console and change directory to the above 'linux SW' directory. Then issue the following two commands 'chmod +x Linux13.305.05.00.03/driver/install' './Linux13.305.05.00.03/driver/install' You will need to run these as root user. After you run the last command, just keep pressing enter untill the software gets installed. Now open the directory /usr/local/MobilePartner using GUI and run MobilePartner.sh. You can run it by clicking on it. This will start a program which is very similar to the program that runs in windows and you can connect evdo using it.

View the article about this video on Sometimes, we need to share files with other computers on the network. In addition to make a shared folder on the computer, we can also make sharing files using network storage, such as NAS. But, the NAS is usually worth quite expensive. Fortunately, some routers provide a USB storage solutions that can be enabled as 'NAS' with a relatively affordable price.

You only need a USB-based external storage media (flashdisk or hard disk). More reviews, news and tutorials.